Today, Samsung CLP-360/365 printer lot of people use. Ex: printer paper jam printer Cover is opened,printer Toner low, printer toner empty, printing, printer sleeping. Each error of printers status or action states have a Led status. We have seven states of the LED status shown: Green Blinking, Green, Off, Red, Red Blinking, Blue Blinking, Blue. The LED light of Printers Samsung CLP-360/365 usually occurs five type: Power LED, Eco LED Status LED Toner LED and WPS LED. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.Īnd make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the 'UPS' (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked.
In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware.After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip - a key).
Graeme Harker liked MAX7000S CPLD JTAG Tester.
#SAMSUNG CLP 365 FIRMWARE FIX LCD CODE#
joran monteiro liked Morse Code USB/HID Interface (The Gadget).Cass liked Solar Powered WiFi Weather Station V4.0.Petoi has added a new log for OpenCat - Open Source Quadruped Robotic Framework.Chris Wheeler liked Dice using Radioactive Decay for True Randomness.Nicholas Jackson has added a new log for Code Breakdown: (v3.5.4) PowerShellEditorServices.Chris Wheeler liked Flux Capacitor Badge.pinderschloss on Digital Kitchen Spoon Makes Weighing Your Ingredients A Snap.Andy Pugh on Moving Big Stuff Without The Tears.MmmDee on 3D Printed Heat Exchanger Uses Gyroid Infill For Cooling.Capt McAllister on Dropping Marbles With Millisecond Accuracy.Paul on Dropping Marbles With Millisecond Accuracy.Charlie on Recreating The “Stuck Throttle” Problem On A Toyota.doobie on Lighting Up Glue Stick Bicycle Tyres With RGB.Patrick on Moving Big Stuff Without The Tears.John the Programmer on Moving Big Stuff Without The Tears.Posted in hardware, Peripherals Hacks Tagged i2c, laser printer, printer, toner refill Post navigation Check out ’s page reset demo after the break. used a momentary switch, but given this is a once-every-few-months operation, a simple wire would suffice. The final hack that allows to reset the page count and used refilled toner cartridges is a simple wire that ties the SDA line of the EEPROM to ground on boot. Printing a configuration report, he was trilled to see that all page counts have been zeroed. When restarted the printer with the Bus Pirate attached, he noticed it took much longer to initialize. After dumping the data held on this EEPROM with an Arduino and sniffing everything going into the EEPROM with a Bus Pirate, was nearly at his wit’s end. Luckily, figured out a dead simple way to reset the page count so he can use those third-party refill kits.Īll the configuration settings and page counts for the printer are stored on an I2C EEPROM. The printer sends out the ‘low toner’ warning based on page count and won’t print if the page count is too high, negating the economy of a toner refill kit.
#SAMSUNG CLP 365 FIRMWARE FIX LCD FULL#
A full set of toner cartridges sell for about the same price as the printer itself, so figured he could simply refill the toner in the cartridges he already has. Really liked his Samsung color laser printer right up until it was time to replace the toner cartridges.
0 kommentar(er)
